1/2" Sweep Pin For G8 Carbon Wing - Complete (x...
Note: This assembly is made to order This Assembly Contains: 1/2" Diameter Pin, Spacers, Hardwa...
Note: This assembly is made to order This Assembly Contains: 1/2" Diameter Pin, Spacers, Hardware, C2 Oarlock, and 4/4 Pitch Bushings.
G8 Carbon Sweep Wing (Complete)
Note: This assembly is made to order This Assembly Contains: G8 Wing Rigger, 1/2" Pin (w/ hardwar...
Note: This assembly is made to order This Assembly Contains: G8 Wing Rigger, 1/2" Pin (w/ hardware), Pin Cup (w/ hardware), Spread Adjuster Block (w/ hardware), 1/4" Clip On Spacers, C2 Oarlock Product is currently only compatible with the xVIII Small hull (Requires bow-mounted holes drilled in the gunwale).
G8 Carbon Sweep Wing (Wing Only)
Product is currently only compatible with the xVIII Small hull (Requires bow-mounted holes drille...
Product is currently only compatible with the xVIII Small hull (Requires bow-mounted holes drilled in the gunwale).
Two (2) Bolts and Two (2) Lock Washers
Two (2) Bolts and Two (2) Lock Washers
G8 Spread Adjuster Block (w/hardware)
For G8 Carbon Sweep Wing (small xVIII)
For G8 Carbon Sweep Wing (small xVIII)
11.5 inches for Small xVIII hulls. 13 inches for Large xVIII hulls.
11.5 inches for Small xVIII hulls. 13 inches for Large xVIII hulls.
Heel Bracket, Complete (xVIII Footstretcher Pos...
This Assembly contains: Clip, Clip Mount, 2" T-Bolt, P-Nut Handle, Washer
This Assembly contains: Clip, Clip Mount, 2" T-Bolt, P-Nut Handle, Washer
*** MUST INCLUDE SERIAL NUMBER OF BOAT IN ORDER NOTES ***
*** MUST INCLUDE SERIAL NUMBER OF BOAT IN ORDER NOTES ***
Sprint Fin (Fits all 8s and 4s)
Ships with one each of the three fin screw lengths. In order to avoid damaging your fin box, pl...
Ships with one each of the three fin screw lengths. In order to avoid damaging your fin box, please take care to use the correct length when installing your fin. If you have any questions, please contact us!
11.5 inches for Small xVIII hulls. 13 inches for Large xVIII hulls.
11.5 inches for Small xVIII hulls. 13 inches for Large xVIII hulls.
When ordering, please let us know in the checkout notes whether you would like the extra crimp an...
When ordering, please let us know in the checkout notes whether you would like the extra crimp and loop or not. Modern steering setups use a pinch block on one side so the cable components are reusable and dont require use of a crimper to install replacement.
Does not include hardware or pulley mounting clasp (Standard). If you need to replace your entire...
Does not include hardware or pulley mounting clasp (Standard). If you need to replace your entire steering pulley setup, please call in and talk to a representative.
T-Bolts come in two lengths: 1 1/4" & 2" (2" T-Bolts are needed for older xVIII footstretcher...
T-Bolts come in two lengths: 1 1/4" & 2" (2" T-Bolts are needed for older xVIII footstretchers) Please specify which you'd like in the selector
Toebar Tube (xVIII, Post March 2021)
Tube compatible with new fully carbon fiber footstretcher. Toebar tube has a single threaded atta...
Tube compatible with new fully carbon fiber footstretcher. Toebar tube has a single threaded attachment shaft at the center.
x-Plate (xVIII, Post-March 2021)
When purchasing spare parts, note that the Bow/Stroke version is smaller and will fit in any seat...
When purchasing spare parts, note that the Bow/Stroke version is smaller and will fit in any seat if needed. The full sized version would only fit into 2-7 seat. Replacement BatLogic Half-Plates available upon request. Only compatible with these footstretcher parts.
xVIII Foot Height Adjustment Pin, Complete
This Assembly Contains: P-Bolt, Washer, Height Nut Holder w/ inserted Nylock
This Assembly Contains: P-Bolt, Washer, Height Nut Holder w/ inserted Nylock
xVIII Footstretcher, Complete (Post March 2021)
Compatibility Disclaimer: This footstretcher only works with the current xVIII hull(both Small an...
Compatibility Disclaimer: This footstretcher only works with the current xVIII hull(both Small and Large hull), and is not backwards compatible with V8's or any other boat classes. Requires two notched channel tracks for the toebar tube and a sawtooth channel track for the heel bracket.
xVIII Heel Bracket (Pre March 2021)
The xVIII footstretcher has undergone some changes since the model was released. The pictured Hee...
The xVIII footstretcher has undergone some changes since the model was released. The pictured Heel Bracket is intended for an older design before March of 2021 when the adjustable, fully carbon fiber footstretcher was deployed into all new xVIII's.
1 – 22 product(s) of 22
